by Andy Baker
Both lifters and coaches could stand to be a little more creative in finding new ways to keep adding weight to the bar each and every week. Perhaps one of these 5x5 alternatives can help you.
Most of us recognize that doing 5 sets of 5 reps – 5 x 5 – is an incredibly powerful method of getting big and strong. The method is an absolute staple of many of the programs laid out in Practical Programming for Strength Training, 3rd edition. The 5-rep set is right in the “metabolic middle,” the perfect combination for both size and strength. And a whole bunch of 5-rep sets is a powerful stimulus. But this article isn’t about physiology. It’s about training. I want you to walk away from this article today with a piece of information you can train with tomorrow.
That being said, there are multiple ways to employ the 5x5 method into your program. Each method has its own set of pros and cons.
So let’s get to it.
This is probably the most commonly used method of doing 5x5, and will be familiar to a large majority of those reading this article. But for those unfamiliar, “sets across” basically means that all 25 reps are done with the same amount of weight. An example session:
This is by far the hardest method – especially if work sets are approaching that of a 5RM. The benefit of this approach is that it has the potential to create the most stress. The downside is that it has the potential to create the most stress. So going all out on 5x5 across on an exercise like the squat has a tremendous capacity to trigger gains in both size and strength, but it also has the capacity to lead to overtraining. It is also an excellent method for early intermediate lifters to accumulate volume. For a late-stage intermediate, 5x5 across may need to be cycled in with other rep schemes to avoid burnout, or used in conjunction with one of the other 5x5 approaches from this article. For advanced lifters, heavy sets across at this volume will likely be limited to short periods of time (4-8 weeks) before volume must be reduced; otherwise a brush with overtraining can be expected.
No matter the level of training advancement, 5x5 across must be used cautiously by older lifters. If 5 rep sets are to be done heavy, a 40+ lifter might just get the same training effect from 3-4 sets and not run the risk of overtraining. Or he might be better served by using a less stressful variation of the 5x5 protocol.
Ascending sets of 5 involve starting with a light weight set of 5 and progressing up through 5 sets until a limit set of 5 is reached. This method was made most famous by Bill Starr in his classic work The Strongest Shall Survive. There are several key advantages to using this method as opposed to a sets-across approach. First, it’s faster. My guess is that this was the primary reason Starr used this method with his football teams. When going all out with 5x5 across, 8-10 minute rest times between sets are the norm. This often means 40 minutes of rest time alone in a training session, not including warm up sets. For a trainee who wants to get 3-4 exercises in during a training session, this type of drain on his/her time may not be feasible. Using ascending sets, the trainee can usually get through the first three sets on just a couple minutes rest. Prior to his fourth set, he may take 3-5 minutes, and then rest completely (5-10) prior to his limit 5th set. This makes for a much shorter session. For strength coaches or personal trainers who generally have around an hour to work with their clients or athletes, this is can be an ideal approach.
As both pro and con, this method is much less stressful than sets across. For a trainee with limited recuperative abilities (athletes and older trainees) this is a good way to accumulate volume. Additionally these two demographics often require a better warm up than just a general strength trainee. Athletes may be chronically sore and stiff from practice and conditioning, while older folks are generally stiff and sore from being, well, old. The first 2-3 sets at lower weights are a good opportunity for a thorough warm up without wasting a lot of time.
The downside to this method is that it may not generate enough stress to drive adaptation. If this is the case, there are a few “tweaks” you can make. First, simply try adding a set or two. This may mean doing 6 or 7 actual sets instead of just 5. This will “cluster” more work at a higher percentage of your top set. Below is a comparison:
A hybrid ascending sets/sets across approach:
Another way to make an ascending rep scheme more stressful is to add speed to the light weight sets. So in the rep schemes listed above, make your sets at 135, 185, 225, and 275 move more explosively. Accelerating moderate loads at a high velocity is more stressful to the nervous system than moving that same load slowly. For a sport athlete this is absolutely the recommended approach.
Descending sets allow the lifter to work up to his top set of 5 reps faster and with less accumulated fatigue than with ascending sets. Let’s use an example rep scheme of a lifter using 6 ascending sets of 5 to get to a top set of 405x5:
The problem with a setup like this is that the lifter could be handicapping himself on his top set each day. The sets at 365 and 385 are fatiguing enough that they cut into his performance on his top set each day. This will become more pronounced as the lifter grows in strength over time. A simple alternative might be to implement descending sets:
This is much much closer to the stress that a sets across approach would create. But because the weight is dropping each set, the rest time between sets could be greatly reduced, making for a much shorter training session than 5x5 across, but still much longer and more stressful than just doing 5 ascending sets. If the lifter attempts to keep rest times short and do each descending set in a state of incomplete recovery this can be an excellent way to improve work capacity and promote hypertrophy.
February 27 Training Camp (The Squat) : New York, NY
March 11-13 Starting Strength Seminar : Houston, TX
March 12 Training Camp (The Squat) : Atlanta, GA
March 13 Training Camp (Press & Bench Press) : Baltimore, MD
March 19 Training Camp (Press & Bench Press) : Lansing, MI
March 26 Training Camp (Deadlift & Clean) : Atlanta, GA
April 8-10 Starting Strength Seminar : Brooklyn, NY
April 9 Training Camp (Deadlift & Clean) : Chicago, IL
May 6-8 Starting Strength Seminar : Westminster, MD
June 10-12 Starting Strength Seminar : Wichita Falls, TX